Classes and Workshops

Classes ranging from custom gunsmithing to long range shooting

Gunsmithing Classes and Workshops

We are proud to announce a full line of educational products for people interested in furthering their knowledge of firearms and the shooting sports.  Classes in reloading, shooting, gunsmithing, and custom stock work are all offered.

All Classes Include:

  • Small class sizes.
  • Open question periods throughout the class
  • Hands-on experience (where permitted)
  • Lunch Provided
  • Videography permitted

Intro & Beginner Classes

Reloading for Beginners

Starts: TBA

An in-depth overview of reloading products such as; the reloading press, dies, gauges, their role on your bench, and how to get the most out of them.  Immediately followed by setup and use of Full-Length sizing dies and shoulder bump dies.

View Details

Intro Into Chambering for Accuracy

Starts: TBA

A detailed overview of the chambering process.  Barrel defect identification and correction (if possible), dialing in a barrel, cutting, reaming, crowning and polishing a match barrel will all be covered.  This is not a hands-on class but videography is encouraged.

View Details

Stock Inletting

Starts: TBA

Follow NRA Master gunsmith Thomas “Speedy” Gonzalez as he fully inlets a custom stock for use in F-Class competition.  Watch as he preps the stock for work as well as inlets, pillars, and beds the barreled action.  An in-depth conversation about why and how he differs from many others will be given as well as measurable changes that happen during the process.

View Details

Intermediate & Advanced Classes

Advanced Reloading

Starts: TBA

Now is the time to dig into your reloading process and correct the issues that may have been causing you to have unknown fliers or high es/sd numbers.  Students bring their own reloading setups including but not limited to:  presses, dies, powder, primers, brass, and bullets.  Each student, after short discussions about reloading for accuracy, will set up their equipment and begin to identify and eliminate the issues they had previously found.

View Details

Shooting Accurately

Starts: TBA

Focusing on the key elements of short-range benchrest shooting, students will be guided through the procedures and diagnostic identification as to why their groups open up.  Whether that is reloading technique, bag and rest set up, wind calls, or human error, all will be covered in this robust class.  Taught by short-range benchrest hall of fame member, Speedy Gonzalez, this class is a wonderful stepping stone for any shooting discipline.

View Details

Advanced Chambering

Starts: TBA

Students will focus on the finer points of chambering.  Correcting errors as they arrive in real time. Learning how to take in progress measurements, what the readings mean and change on the fly if needed.  Once mastering all of these attributes we hope you will have chamber run out of less than .000050

View Details

Made by Students

Upcoming Workshops

Beginner Chambering

TBA

Students will learn about the lathe, common parts, tooling, and functions.  They will then learn how to properly dial in a barrel, chamber, and thread to competition standards.

View Details

Stock Inletting

TBA

Students will observe and discuss proper stock set-up in a Sharp Knee Mill and the tools used during inletting.  Then they will witness the inletting of a custom stock used for short-range benchrest or F-Class competition.  This is a fully immersive class with question and answer periods throughout the day.

View Details

Advanced Chambering

TBA

This will be a group of 5 for the post F-Class Nationals held in Raton, NM.  The drive from Raton to San Antonio is approximately 9 hours. We will be covering various chambering idiosyncracies and how to identify and correct them.  Hopefully, leading to a chamber with a run out of .000050

View Details

Expert Instructors

Through hard work, endless study, and the dedication to the shooting sports, the SG Precision Group has developed a methodology that has been proven on the firing line time and time again.

Speedy Gonzalez

Speedy Gonzalez

Head of Production

Greg Taylor

Greg Taylor

Head Of Finance and Procurement

Kalen Gilstrap

Kalen Gilstrap

Gunsmith

From Our Students

Coming Soon

Coming Soon

Get In Touch

Please email us if you have any questions regarding a product, class or service.

Address

9023 Huebner Rd #102
San Antonio, TX 78240

Call Us

303.802.7008

Email Us

greg@sgprecisionllc.com
speedy@sgprecisionllc.com